HYD3010 Hydraulic Drive Kit | Triplex Pump

HYD3010 | Hydraulic Motor Pump Drive Unit | 8 GPM 2200 PSI | AR XW Series

HYD3010 is Annovi Reverberi’s 8 GPM answer to the most common step-up question in hydraulic washdown: what comes after the 4 GPM class? Built as the HYD-XW30.10 drive unit — an XW-series triplex plunger pump direct-coupled to a Sauer Danfoss hydraulic motor through the F38 flange — it delivers 8.0 GPM (30.2 L/min) at up to 2200 PSI (150 bar) at 1450 RPM. Twice the rinse volume of the RK-class packages at the same commercial working pressure, without stepping up to the big-frame RTX units and the heavier hydraulic supply they demand.

That middle position is exactly where a large share of real washdown lives. Fleet and municipal equipment that a 4 GPM unit cleans too slowly. Agricultural machinery shedding mud by the shovelful. Service and utility trucks whose wash duty grew with the route. Contractor rigs that need production pace without production hydraulics. The HYD3010 covers all of it from an auxiliary circuit most machines already carry.

HYD3010 Specifications

• SKU: HYD3010
• Configuration: Hydraulic drive unit — AR HYD-XW30.10: pump and Sauer Danfoss motor, F38 close-couple
• Pump: Annovi Reverberi XW-series triplex plunger pump (194-series frame)
• Flow Rate: 8.0 GPM (30.2 L/min)
• Maximum Discharge Pressure: 2200 PSI (150 bar)
• Rated Speed: 1450 RPM — never overspeed
• Pump Power Requirement: Approximately 11 HP at full duty
• Hydraulic Motor: Sauer Danfoss — max 9.5 GPM (36 L/min), max 2,610 PSI (180 bar)
• Pump Inlet Port: 3/4″ F
• Pump Discharge Port: 3/8″ F
• Maximum Fluid Temperature: 140°F
• Pump Head: Brass, with one-piece ceramic plungers
• Replacement Pump: AR21655 (pump only, without flange)

Hydraulic Supply Requirements

Full 8 GPM at 2200 PSI performance calls for approximately 9.5 GPM (36 L/min) of continuous oil flow at working pressure up to the Danfoss motor’s 2,610 PSI (180 bar) rating — roughly 14 hydraulic horsepower. That envelope fits squarely inside standard skid steer auxiliaries, tractor remotes, and truck hydraulic systems: the HYD3010 asks for meaningfully less circuit than the 13+ GPM class while delivering twice the water of the 4 GPM tier. Protect the motor with a relief set at or below 2,610 PSI on circuits that relieve higher, route return oil short and filtered to tank, and provide oil cooling for continuous trigger-on duty. With less flow available the unit runs proportionally slower; full water pressure always requires full supply pressure at the motor. Call WSHPWR with your machine’s auxiliary numbers and we will confirm the match.

The Step-Up Sweet Spot

Washdown time scales with flow: at 8 GPM, jobs finish in half the passes a 4 GPM package needs, which across a fleet day is the difference between washing being a task and being the schedule. Yet the HYD3010’s ~14 hydraulic HP demand keeps it inside ordinary auxiliary circuits — no dedicated power unit, no engineered cooling package, no platform jump. For operations that outgrew the RK class but cannot justify RTX-class hydraulics, this drive unit is the whole answer, which is why the XW30.10 platform has quietly become one of AR’s most fielded hydraulic units.

Direct-Drive Simplicity and the Repair Path

The Danfoss motor mounts to the pump through AR’s F38 close-couple flange — one centerline, no belts, pulleys, guards, or field alignment, minimal side loading on bearings and seals, and output independent of host engine speed. Just as valuable years from now: when the wet end finally wears out, the AR21655 replacement pump restores factory performance while your motor, flange, and mounting hardware transfer over — the lowest-cost repair path in the class, and one WSHPWR stocks alongside the complete unit.

XW-Series Construction

The 194-series frame carries a corrosion-resistant brass head with stainless wet-end components, one-piece ceramic plungers for heat dissipation and abrasion resistance, and a die-cast aluminum crankcase with oil monitoring. Valve access through the head keeps routine inspection quick, and AR repair kits keep the service path standard for any shop maintaining AR equipment.

Installation & Operation Notes

Mount horizontally and confirm motor rotation at commissioning. Feed the 3/4″ inlet from a flooded, filtered supply with short, unrestricted plumbing — 8 GPM rewards a buffer tank on marginal water sources. Pair the discharge with an unloader set against working pressure, verify the hydraulic relief against the motor’s 2,610 PSI ceiling, size nozzle orifices to the 8.0 GPM duty point, hold 1450 RPM as the ceiling, and winterize before cold-weather storage.

Quality Assurance & Maintenance

Every HYD3010 ships factory-tested for flow rate, pressure stability, and vibration. Maintenance follows AR’s standard schedule — crankcase oil changes, seal inspection, periodic valve checks with AR repair kits — and when major service eventually comes, the AR21655 pump swap returns the unit to day-one performance without repurchasing the drive.

HYD3010 Key Features & Applications

• 8.0 GPM at 2200 PSI, 1450 RPM — twice the water of the 4 GPM class at the same commercial pressure.
• Complete drive unit: AR XW pump and Sauer Danfoss motor on the F38 close-couple flange.
• Runs on ~9.5 GPM of oil at up to 2,610 PSI (~14 hydraulic HP) — standard auxiliary circuits qualify.
• Documented repair path: AR21655 replacement pump reuses your motor and flange.
• Brass head, ceramic plungers, and standard AR repair kits on the 194-series frame.
• Ideal for fleet and municipal washdown, agricultural equipment cleaning, service and utility trucks, and contractor rigs stepping up from the 4 GPM tier.