XTA2G15EBA-F8 Triplex Pump | 2.0 GPM 1500 PSI 1750 RPM

Annovi Reverberi XTA2G15EBA-F8 Triplex Pump | 2.11 GPM 1800 PSI F8 NEMA 56C Electric Flange

The XTA2G15EBA-F8 from Annovi Reverberi is a commercial-grade
slow-speed triplex plunger pump delivering 2.11 GPM at 1,800 PSI
at 1,750 RPM — engineered for NEMA 56C electric motor mounting via
an F8 hollow shaft flange for commercial electric pressure washers,
HVAC and coil cleaning systems, equipment wash bays, contractor portable electric
rigs, and light industrial cleaning applications where a slow-speed triplex
architecture, forged brass manifold construction, and 5/8-inch electric shaft
compatibility deliver long service life and consistent performance on a compact
10-lb platform. The XTA2G15EBA-F8 is part of Annovi Reverberi’s
Series 132 XTA commercial pump family — a proven triplex crank design operating
at 1,750 RPM where reduced speed directly lowers heat generation, minimizes bearing
fatigue, and extends seal service life versus the 3,400 RPM direct-drive
alternatives in the same F8 NEMA 56C mounting class.

The XTA2G15EBA-F8 arrives factory-tested, pre-filled with 10 oz
of break-in oil, and equipped with an oil sight glass and vented dipstick for
complete daily crankcase monitoring — backed by a 5-year manufacturer
warranty with nationwide service support. Note: the XTA2G15EBA-F8 does
not include an integrated unloader valve; a correctly rated external unloader
must be specified and installed for proper system pressure regulation
and pump protection.

XTA2G15EBA-F8 Key Specifications

Performance, Drive & Construction — Confirmed AR Catalog Data

• Model: Annovi Reverberi XTA2G15EBA-F8
• Series: 132 (XTA) — commercial triplex
  plunger platform
• Max Flow Rate: 2.11 GPM (8 L/min) —
  commercial-grade output for electric pressure washers,
  HVAC coil cleaning, and light
  industrial applications
• Max Pressure: 1,800 PSI (124 Bar) —
  effective cleaning force for equipment washdown, surface
  cleaning, and commercial contractor
  applications
• EBHP: 2.6 — effective brake horsepower
  at rated duty point
• Operating Speed: 1,750 RPM — slow-speed
  design reduces heat, vibration, and component wear for
  extended continuous-duty service life
• Bore Diameter: 15 mm |
  Stroke: 9.6 mm |
  CSID Stamp: 5
• Shaft: 5/8-inch hollow — Electric ‘E’ shaft
  version for NEMA 56C face electric
  motor coupling
• Flange: F8 — direct mount for NEMA 56C
  face electric motors
• Pump Type: Triplex plunger crank —
  three-cylinder balanced design for smooth, low-pulsation
  output at rated 1,800 PSI
• Manifold: Forged brass — superior pressure
  resistance and corrosion performance versus cast brass
  alternatives at 1,800 PSI commercial duty
• Connecting Rods: Aluminum — weight-optimized
  specification appropriate for 1,750 RPM commercial
  duty cycling
• Valves: Stainless steel check valves —
  consistent sealing strength and reliability across
  commercial duty cycles
• Inlet: 1/2-inch female |
  Outlet: 3/8-inch female
• Max Water Temperature: 140°F
• Oil Capacity: 10 oz
• Weight: 10 lbs
• Pump Orientation: Horizontal
• Market Classification: Commercial
• Unloader: Not included — external unloader
  valve required for system pressure regulation
  and pump protection
• Warranty: 5-year manufacturer warranty with
  nationwide service support

What Comes with the XTA2G15EBA-F8

Factory-Tested and Ready for NEMA 56C Motor Installation

• Factory-tested pump assembly — every
  XTA2G15EBA-F8 is pressure-verified before shipment
• Pre-filled break-in oil (10 oz) —
  factory-installed for immediate commissioning without
  sourcing initial oil fill separately
• Oil sight glass — quick visual crankcase
  oil level inspection before each operating session
  without tools or disassembly
• Vented dipstick — crankcase pressure
  balance and secondary oil level verification for
  complete routine maintenance checks
• Operator’s manual and parts schematic —
  installation reference, maintenance procedures, and
  parts identification for the life
  of the pump
• 5-year manufacturer warranty documentation —
  with nationwide service center coverage

How the XTA2G15EBA-F8 Works

Slow-Speed Triplex Crank Design for 1,800 PSI Commercial Electric Performance

The XTA2G15EBA-F8 uses a triplex crank design where three ceramic
plungers driven by aluminum connecting rods operate in a synchronized reciprocating
sequence — each cylinder drawing water through stainless steel check valves at the
1/2-inch female inlet and discharging at rated 1,800 PSI through stainless discharge
valves at the 3/8-inch female outlet. The overlapping three-cylinder cycle produces
smooth, consistent flow with substantially reduced pulsation compared to axial cam
or wobble-plate pump designs at equivalent output — protecting downstream hoses,
spray guns, and HVAC cleaning accessories from hydraulic fatigue across
commercial operating sessions.

The F8 hollow shaft flange couples the XTA2G15EBA-F8 directly to
the 5/8-inch output shaft of compatible NEMA 56C face electric motors — a secure,
direct drive connection that eliminates belts, pulleys, and separate coupling
hardware for clean installation in electric pressure washer systems and
contractor portable rigs.

At 1,750 RPM, the XTA2G15EBA-F8 operates significantly slower
than the 3,400 RPM axial cam alternatives in the same NEMA 56C mounting class —
the reduced operating speed directly lowers heat generation at the ceramic plunger
and packing interface, minimizes bearing surface velocity under sustained load,
and slows the fatigue cycling rate on stainless check valve seats. For commercial
operators running the XTA2G15EBA-F8 through regular daily
cleaning cycles, this translates into longer intervals between seal replacements,
more consistent 1,800 PSI output over time, and a pump that outlasts higher-speed
alternatives in continuous-duty commercial electric
pressure washer applications.

The forged brass manifold provides superior pressure resistance
and structural integrity at 1,800 PSI versus the cast brass manifolds found in
competing electric pump alternatives at this price point — forged construction
delivers measurably better grain structure and sealing surface quality that
maintains dimensional stability across long commercial service intervals.

XTA2G15EBA-F8 Key Benefits

Why Slow-Speed Triplex Outperforms 3,400 RPM Axial Cam in Commercial Daily Use

• 1,750 RPM slow-speed triplex vs. 3,400 RPM axial cam:
  the XTA2G15EBA-F8 runs at half the speed of axial cam
  alternatives in the same F8 NEMA 56C mounting class —
  every operating hour at 1,750 RPM means less heat,
  less seal cycling, less valve fatigue, and reduced
  bearing load versus 3,400 RPM
  direct-drive alternatives
• Triplex crank smoothness protects accessories:
  the synchronized three-cylinder cycle produces substantially
  lower pulsation than axial cam designs — less hydraulic
  shock transmitted to downstream hose assemblies,
  spray guns, and HVAC cleaning accessories across
  daily commercial operating sessions
• Forged brass manifold at the commercial price point:
  forged construction provides superior pressure resistance
  and grain structure versus cast brass manifolds common
  in competing electric pumps — the XTA2G15EBA-F8 delivers
  genuine forged brass quality at a price appropriate
  for commercial replacement
  pump applications
• 1,800 PSI max pressure — above the class standard:
  the XTA2G15EBA-F8’s rated maximum exceeds the 1,500 PSI
  commonly listed for competing pumps in this mounting
  class — meaningful additional headroom for commercial
  operators who occasionally need extra
  cutting pressure
• 2.11 GPM confirmed max flow: actual rated
  maximum flow confirmed from AR product data — slightly
  above the 2.0 GPM commonly marketed for competing
  pumps in this class
• F8 NEMA 56C — the standard commercial electric
  motor interface: direct-fit for the most common
  commercial electric pressure washer motor configuration —
  replacement installation without adapter plates or
  custom hardware on compatible systems
• Oil sight glass and dipstick for fast daily checks:
  10 oz crankcase oil level verified in seconds before
  each use — the most critical routine maintenance habit
  for XTA2G15EBA-F8 bearing longevity
  at 1,750 RPM
• 5-year warranty — exceptional for this pump class:
  most competing commercial NEMA 56C electric triplex pumps
  carry 1–2 year warranties — the XTA2G15EBA-F8’s 5-year
  coverage reflects Annovi Reverberi’s confidence in
  the Series 132 platform’s
  commercial durability

XTA2G15EBA-F8 Typical Applications

Where 2.11 GPM at 1,800 PSI on an F8 NEMA 56C Mount Delivers Results

• Commercial electric pressure washers:
  the XTA2G15EBA-F8’s slow-speed triplex design and forged
  brass manifold make it a proven upgrade and replacement
  pump for commercial-grade NEMA 56C electric
  pressure washer systems requiring better
  durability than axial cam alternatives
• HVAC and coil cleaning systems: steady
  1,800 PSI output with low pulsation is appropriate for
  controlled coil cleaning where consistent pressure and
  smooth flow protect delicate fin surfaces from
  hydraulic shock damage
• Equipment wash bays: workshops, industrial
  facilities, and small-scale manufacturing wash stations
  where continuous-duty electric pump operation demands
  the service life advantage that the XTA2G15EBA-F8’s
  1,750 RPM design provides over
  3,400 RPM alternatives
• Food service and commercial kitchen cleaning:
  equipment and surface cleaning in commercial kitchen
  environments where 1,800 PSI output with electric
  zero-emission operation meets indoor
  air quality requirements
• Contractor portable electric rigs: compact
  10-lb weight and NEMA 56C direct mounting make the
  XTA2G15EBA-F8 practical for portable contractor
  systems where pump weight and installation simplicity
  both matter
• General commercial surface cleaning: patios,
  sidewalks, vehicles, and outdoor furniture in commercial
  property maintenance where consistent 1,800 PSI electric
  output handles routine daily cleaning tasks efficiently

XTA2G15EBA-F8 Installation & Maintenance

Best Practices for Long Service Life at 1,800 PSI

• Verify NEMA 56C motor compatibility: confirm
  the electric motor has a 5/8-inch output shaft and NEMA
  56C face configuration — the XTA2G15EBA-F8 F8 flange
  is specifically engineered for this
  motor standard
• Install an external unloader valve: the
  XTA2G15EBA-F8 does not include an integrated unloader —
  a correctly rated external unloader valve sized for
  1,800 PSI and 2.11 GPM must be installed for proper
  pressure regulation and pump protection
  at every trigger release event
• Use clean, filtered water: install an
  upstream strainer at the 1/2-inch female inlet to protect
  ceramic plungers and stainless check valves from
  particulate contamination
• Check oil before every use: use the sight
  glass for visual confirmation and dipstick for secondary
  verification — 10 oz crankcase capacity; adequate oil
  is the most critical factor in XTA2G15EBA-F8 bearing
  longevity across daily commercial use
• Never run dry: always confirm water supply
  is connected and flowing before starting — dry operation
  damages ceramic plunger packings and voids
  the 5-year warranty
• Do not exceed 140°F maximum water temperature:
  confirmed AR specification limit for the
  XTA2G15EBA-F8 — hot-water operation above this
  threshold accelerates seal degradation
• First oil change at approximately 50 hours:
  then follow Annovi Reverberi’s maintenance schedule —
  commercial daily-use applications benefit from more
  frequent oil changes than occasional
  residential use
• Flush after chemical applications: run clean
  water through the XTA2G15EBA-F8 after every detergent
  or chemical use to protect the forged brass manifold
  passages and stainless valve seats
• Winterize before cold storage: drain completely
  or use pump-safe antifreeze — freeze damage to the
  forged brass manifold or plunger components
  voids warranty coverage

Why Choose the Annovi Reverberi XTA2G15EBA-F8

Slow-Speed Triplex Commercial Performance for NEMA 56C Electric Systems

• The slow-speed choice in the F8 NEMA 56C class:
  1,750 RPM triplex crank versus 3,400 RPM axial cam —
  when commercial daily-use longevity matters more than
  compact size or initial cost, the XTA2G15EBA-F8’s
  slow-speed architecture is the correct
  specification choice
• 1,800 PSI and 2.11 GPM — above class standard:
  AR-confirmed rated maximum specifications that exceed
  the commonly marketed 1,500 PSI / 2.0 GPM figures
  for competing pumps in this mounting
  class and price range
• Forged brass manifold quality at a replacement
  pump price: the XTA2G15EBA-F8 delivers forged
  brass construction — the manifold standard of
  commercial-grade pump design — in a compact NEMA 56C
  electric pump package
• Series 132 XTA proven commercial platform:
  the AR Series 132 XTA family has accumulated extensive
  commercial field use as a replacement and OEM pump
  for electric pressure washer systems — proven
  durability across commercial
  operating environments
• Annovi Reverberi quality since 1958: over
  60 years of commercial pump manufacturing expertise —
  the XTA2G15EBA-F8 carries that heritage into a compact
  NEMA 56C electric pump platform built to
  AR’s commercial specifications
• 5-year warranty where competitors offer 1–2 years:
  exceptional coverage that signals genuine confidence in
  the XTA2G15EBA-F8’s commercial duty durability — backed
  by U.S.-based nationwide
  service support
• Backed by WSHPWR: application support, motor
  compatibility guidance, external unloader valve
  specification assistance, and full parts availability
  for the XTA2G15EBA-F8 and the complete Annovi
  Reverberi XTA pump family

The Annovi Reverberi XTA2G15EBA-F8 delivers 2.11 GPM at
1,800 PSI at a slow-speed 1,750 RPM through a
5/8-inch hollow shaft F8 NEMA 56C flange — a Series 132 commercial
triplex crank pump built with forged brass manifold, ceramic plungers, and stainless
steel check valves for commercial electric pressure washers, HVAC coil cleaning,
equipment wash bays, and contractor electric rigs where slow-speed triplex
durability, AR-confirmed 1,800 PSI maximum pressure, and 5-year commercial
warranty coverage outperform the 3,400 RPM axial cam alternatives in the same
NEMA 56C mounting class. Contact WSHPWR for current pricing, availability, motor
compatibility confirmation, external unloader sizing guidance,
and application support.