14880RT-UR-C GFCI Assembly UL Listed | No-Cord Protection Module

14880RT-UR-C GFCI

14880RT-UR-C — Inline GFCI Assembly UL Listed, No Cord | Safety
The AR 14880RT-UR-C is a compact, inline ground-fault circuit interrupter (GFCI) assembly designed to add a dependable
layer of electrical protection to electric pressure washers and other corded tools working around moisture, conductive
spray, and frequent handling. UL listing confirms that the device has been evaluated to recognized safety standards, and
the cord-free format lets OEMs and service teams place protection exactly where it belongs in the circuit—between the
power inlet and the machine’s internal switch or control block—without extra cord length, bulky dongles, or additional
joints that can snag in the field.

Safety & Protection

• Inline ground-fault protection: monitors current on the hot and neutral conductors and opens the
  circuit when an imbalance indicates a fault path to ground, removing power before a minor issue becomes a hazard.
• UL listed device: supports code compliance, safety audits, and standardized builds across fleets
  and production runs.
• Test / Reset interface: simple controls provide clear status at a glance—Reset establishes
  protected power, while Test simulates a fault so users can verify proper trip operation.
• Supports safe work practices: complements basic controls such as intact insulation, drip loops,
  and dry hands at the plug in wet pressure-wash environments.

Design & Integration of 14880RT-UR-C

• Cord-free assembly: installs inside an enclosure or on a protected panel, keeping protection close
  to the load without adding clutter at the outlet.
• Installer-friendly layout: route conductors with gentle bends, use appropriate strain relief, and
  secure the housing with hardware so vibration does not loosen terminals over time.
• Clear labeling: distinct line and load markings plus documented wiring layout help technicians
  trace power quickly during troubleshooting or inspection.
• Tidy wiring plan: fewer dangling connections and twists in the power path reduce fatigue on plugs
  and receptacles and keep the work area around vehicles, siding, or equipment less cluttered.

Commissioning & Operation

• Pre-start checks: before energizing a system, verify tight terminations, correct polarity, seated
  gaskets and strain reliefs, then press Reset to establish protected power.
• Functional test: with the unit powered, press Test and confirm that the machine does not run; press
  Reset again to restore operation. This quick preflight—usually seconds—helps prevent nuisance surprises later in
  the shift.
• Trip behavior: repeated trips under normal load should be treated as a signal to investigate cables,
  connectors, motors, or heaters for damage or moisture rather than simply resetting.

Maintenance & Best Practices

• Route wiring away from sharp edges and moving components; keep the Test/Reset face clean so indicators remain
  visible.
• Allow the housing to dry if heavily splashed before operating the buttons.
• During routine maintenance, de-energize the circuit, inspect for heat discoloration or moisture intrusion, and
  verify that mounting hardware is secure.
• Encourage a quick functional test after storage, transport, or any repair that touches the power path.
• Train operators to keep cord connections off the ground where practical, coil cords loosely to avoid kinks, and
  avoid routing power through standing water.

Fleet & Facility Advantages

• Standardized interface: using the same UL-listed GFCI 14880RT-UR-C assembly across multiple models simplifies
  documentation, training, and replacement planning.
• Audit-ready: a clearly marked, testable GFCI at the machine level is easy to verify during safety
  inspections or lockout/tagout reviews.
• Upgrade path: ideal for upgrading older washers, cleaning up field repairs that relied on external
  cord GFCIs, or designing new production units with built-in protection.

Assembly UL Listed
The 14880RT-UR-C, GFCI assembly, is UL listed, has no cord, it is inline protection, it is Test/Reset, compatible for electric pressure washers, it has moisture
safety, it is ground fault protection, it is compact install.