HYD-RTP30.60N Hydraulic Drive Kit | 7.9 GPM 8700 PSI

HYD-RTP30.60N | Hydraulic Drive Kit | 7.9 GPM 8700 PSI | 600 Bar Apex

HYD-RTP30.60N is the highest pressure in the WSHPWR hydraulic catalog: Annovi Reverberi’s 600-bar industrial platform — 7.9 GPM (30 L/min) at up to 8700 PSI, per AR North America’s published ratings — on the 1000 RPM frame, in the N-version solid-shaft build for coupled drives. Six hundred bar is the class above the class: twenty percent more jet energy than the 500-bar units that define ordinary UHP work, aimed at the removals where even those stall — thick-film and glass-flake linings, aged multi-coat epoxy systems, vulcanized rubber, calcified scale in exchanger bundles, and the concrete cuts that 7250 PSI only scores.

AR builds this rating on the heaviest small-frame architecture it makes: a 144-pound industrial pump whose 1000 RPM pace, per-ARNA 50-horsepower drive rating, and UHP wet end treat 600 bar as the design point. For the contractors and plants whose work lives at the top of the removal spectrum, this is the pump that ends the “will water do it?” conversation — and the solid shaft leaves the drive architecture to the system engineered around it.

HYD-RTP30.60N Specifications

• SKU: HYD-RTP30.60N
• Configuration: Solid-shaft UHP industrial pump — N version, for coupled or belt drive
• Pump: Annovi Reverberi 600-bar industrial platform (30.600 class)
• Flow Rate: 7.9 GPM (30 L/min), per AR North America
• Maximum Discharge Pressure: 8700 PSI (600 bar)
• Rated Speed: 1000 RPM — never overspeed
• Power Requirement: 50 HP at full duty, per AR North America
• Inlet Port: 3/4″ F
• Discharge Port: 3/8″ F
• Weight: Approximately 144 lbs (65 kg), per AR North America
• Maximum Fluid Temperature: 140°F
• Wet End: UHP-rated head and valve architecture with ceramic plungers
• Shaft: Solid (N version) — coupling interface confirmed at order

Drive Options for the Solid Shaft

Full duty asks roughly 60 hydraulic horsepower delivered continuously, and the solid shaft accepts the architecture that supplies it: a bent-axis piston motor through a flex coupling or bell housing — the Sunfab SCM class WSHPWR stocks for this frame family — an electric motor geared to 1000 RPM on a common base, or an engine drive through reduction. Align to coupling specification, guard the drive, relieve the hydraulic side within the motor’s rating, and engineer reservoir volume, return filtration, and oil cooling for continuous duty; at 600 bar the power system is half the machine. Call WSHPWR with your circuit’s numbers and we will spec the complete drive before you order.

What 600 Bar Finishes

Every removal has a release threshold, and the industrial world’s hardest jobs sit between 500 and 600 bar. Glass-flake and novolac linings engineered to survive chemical service; rubber vulcanized to steel; decades of repaint layered into a single stubborn film; mineral scale grown dense in exchanger tubes — materials where 7250 PSI chases and 8700 PSI finishes. The extra energy also buys speed on everything below the threshold: work a 500-bar unit completes slowly, this class completes at pace. It remains water — no grit logistics, no chemical drums, no dust plume — which is why the top of the surface-prep trade runs 600-bar pumps as standard equipment, not exotica.

The Frame That Carries the Number

At 8700 PSI, every stroke is an event, and the platform’s whole build answers for it: 1000 RPM winds the stroke-count wear clock a third slower per gallon than compact-frame speeds, the industrial crankcase carries the torque pulsation of 600-bar plunger loading, and the serviceable wet end keeps the genuine maintenance this class demands — packings, valves, seals on schedule — inside a maintenance window. AR publishes the ratings; the 144-pound frame is what makes them honest for years.

HYD-RTP30.60N – UHP Safety Is a System

At 8700 PSI, water cuts. Every downstream component — hose, fittings, lance, nozzles — must be rated for the 600-bar class with margin, inspected on schedule, and retired on condition; 500-bar hardware does not cross over, and pressure-washing hardware is not in the conversation. Operators need UHP-specific training, protective equipment, and controlled work zones; dump-style controls and correct relief protection are non-negotiable. WSHPWR supplies UHP-rated accessories and will help spec the complete, compliant circuit — at this class, the system is the product.

Quality Assurance & Maintenance

Every HYD-RTP30.60N is factory-tested for flow rate, pressure stability, and vibration before shipment. Maintenance follows the strictest UHP discipline in the catalog: scheduled crankcase oil service, packing and seal intervals proportional to 600-bar duty, valve inspection on hours, and AR repair kits keeping the path standard. Engineered onto a correct drive and held at 1000 RPM, the apex spec runs a career at the top.

HYD-RTP30.60N Key Features & Applications

• 7.9 GPM at 8700 PSI (600 bar) — the highest pressure in the WSHPWR hydraulic catalog, per AR North America’s ratings.
• Finishes the removals 500 bar chases: glass-flake linings, vulcanized rubber, multi-coat systems, dense scale.
• Solid shaft (N version) — hydraulic, electric, or engine drive; ~60 hydraulic HP continuous.
• 144-pound industrial frame at 1000 RPM: the stroke economics that make 600 bar a career.
• Water-only method: no grit logistics, no chemical inventory, no dust plume.
• Ideal for the hardest coating and lining removals, exchanger and tube descaling, marine and infrastructure prep at the top of the spectrum, and engineered 600-bar truck and skid systems.