XMV3G25D-F33C2I 3.0 GPM 2500 PSI Pump | 3400 RPM F33C2I

XMV3G25D-F33C2I by Annovi Reverberi — Triplex Plunger Pump with Gymatic Unloader and Chemical Injector | 3.0 GPM | 2,500 PSI | NEMA 56C Electric Motor Mount | XM Series Commercial Platform

The XMV3G25D-F33C2I by Annovi Reverberi is a commercial-grade XM Series triplex ceramic plunger pump engineered for electric motor-driven pressure washing systems that require 2,500 PSI output, integrated downstream chemical application capability, and the structural durability of AR’s commercial high-pressure pump platform in an electrically driven configuration. Rated at 3.0 GPM and 2,500 PSI at 3,400 RPM, the XMV3G25D-F33C2I mounts directly to NEMA 56C-frame electric motors via its F33 flange — delivering smooth, consistent high-pressure cleaning performance for fixed wash bays, indoor facilities, fleet maintenance stations, rental operations, and any installation where engine-driven operation is impractical or restricted.

What distinguishes the XMV3G25D-F33C2I from electrically driven XTV Series pumps at similar output ratings is its XM Series platform — the commercial high-pressure pump family AR engineers for sustained operation at the upper end of the pressure range. The XM Series manifold, valve, and crankcase architecture bring additional structural margin to the 2,500 PSI electric-drive application, making this pump the preferred specification for continuous-duty commercial wash stations, high-utilization rental installations, and fixed facility environments where uptime and rebuild intervals matter most.

Built by Annovi Reverberi in Modena, Italy — with US-based operations, a domestic parts distribution network, and dedicated AR North America technical support — the XMV3G25D-F33C2I arrives as a complete, factory-tested assembly. Pre-filled with AR break-in oil, equipped with a Gymatic unloader and active downstream chemical injector, and packaged with mounting bolts and fasteners, a vented dipstick, operator’s manual, and full parts schematic, this pump is ready to install from the moment it arrives. Protected by a 5-year US limited warranty through AR North America and built to be fully rebuilt rather than replaced, the XMV3G25D-F33C2I is a long-term investment in a commercial pump platform capable of a decade of productive service life.

Decoding the XMV3G25D-F33C2I Model Number

What Every Segment of This AR Pump Designation Tells You

Annovi Reverberi encodes all critical specification data — pump series, performance output, shaft type, flange interface, unloader family, and injector configuration — directly into the model number. Reading the XMV3G25D-F33C2I correctly before specifying confirms motor compatibility, shaft engagement, and chemical feed configuration:

• XMV — Pump series: XM Series triplex plunger pump — AR’s commercial high-pressure platform with forged brass manifold construction, engineered for sustained 2,500–3,000 PSI operation
• 3G25 — Performance rating: 3.0 GPM flow rate at 2,500 PSI maximum operating pressure
• D — Shaft version: Direct Drive — hollow crankshaft bore for coupling to the drive shaft. On this XM Series model paired with the F33 NEMA 56C flange, the D designation accommodates the pump’s crankshaft bore for direct electric motor shaft engagement, consistent with the XM Series’ dual-compatibility architecture for NEMA 56C-coupled applications
• F33 — Flange type: NEMA 56C close-coupling flange for XMA(SS) and XMV Series — compatible with both 5/8″ and 3/4″ I.D. shaft configurations for close coupling to NEMA 56C-frame electric motors (AR part AR1780910). This is the XM Series-specific NEMA 56C interface, distinct from the F8 flange used on XTV Series electric-drive pumps.
• C2 — Unloader code: Gymatic (C2 = Gymatic per AR suffix designation) — Gymatic series internal bypass unloader, brass body, adjustable pressure regulation, factory-fitted
• I — Chemical injector: Included — a downstream soap and chemical injector is integrated into the Gymatic unloader assembly, enabling low-pressure detergent application without a separate injector fitting

F33 vs F8 — XM Series vs XTV Series NEMA 56C Flanges

Both the F33 and F8 flanges provide NEMA 56C electric motor close-coupling interfaces, but they serve different pump series and are not interchangeable:

• F33 flange (this model) — the NEMA 56C interface for XMA(SS) and XMV Series pumps (AR1780910). The XM Series platform brings commercial high-pressure construction to the electric-drive application — forged brass manifold, XM Series crankcase architecture, and the structural margins of a platform engineered for 2,500–3,000 PSI sustained duty.
• F8 flange — the NEMA 56C interface for XTV and XTA Series ‘E’ version pumps (AR1584). The XTV platform is designed for standard commercial-duty electric applications at 1,500–2,200 PSI where the XM Series’ additional structural margin is not required.

Specifying the XMV3G25D-F33C2I over an equivalent-output XTV Series electric pump reflects a deliberate choice of platform — XM Series construction for applications demanding greater durability, longer rebuild intervals, and higher continuous-duty uptime at 2,500 PSI.

Key Specifications

XMV3G25D-F33C2I Technical Details at a Glance

• Flow Rate: 3.0 GPM (gallons per minute)
• Maximum Pressure: 2,500 PSI
• Operating Speed: 3,400 RPM
• Pump Type: Triplex ceramic plunger pump — three-piston crankshaft-driven design for smooth, consistent, high-pressure output
• Manifold Material: Forged brass — dense, pore-free construction for corrosion resistance and sustained 2,500 PSI cycle integrity
• Plungers: Solid ceramic — exceptional hardness, wear resistance, and chemical inertness across extended commercial operating hours
• Valves: Stainless steel — precise seating geometry, scale resistance, and reliable performance under continuous 2,500 PSI cycling
• Flange: F33 — NEMA 56C close-coupling flange for XMV Series, 5/8″ or 3/4″ I.D. shaft (AR part AR1780910)
• Unloader System: Gymatic series (C2 code) — brass-body internal bypass unloader, adjustable pressure regulation, rated above 2,500 PSI operating range within AR’s accepted 15% variance
• Chemical Injector: Included — downstream venturi injector integrated into Gymatic unloader assembly (“I” suffix confirmed)
• Warranty: 5-year limited warranty — US-based coverage through AR North America with domestic parts and service support

What’s Included in the Box

A Complete, Factory-Configured Assembly Ready for Installation

Every XMV3G25D-F33C2I ships fully assembled and field-ready:

• Factory-installed Gymatic unloader (C2) with active chemical injector — pre-mounted with integrated downstream injector ready for detergent supply line connection
• AR factory break-in oil — crankcase pre-filled to the correct operating level for first startup without modification
• Vented dipstick — enables fast, accurate crankcase oil level checks while maintaining proper crankcase pressure relief during operation
• Clear oil sight glass — at-a-glance oil level monitoring without removing the dipstick cap
• Mounting bolts and fasteners — hardware pre-selected and sized for F33 NEMA 56C face-mount installation on compatible electric motors
• Operator’s manual — complete installation, startup, operating, and maintenance procedures including oil change intervals, winterization protocol, and chemical injector care
• Parts schematic — exploded-view diagram with AR part numbers for every serviceable pump component for field and shop reference
• Factory test certification — every XMV3G25D-F33C2I load-tested at 50%, 100%, and 150% of rated output before leaving the AR manufacturing facility

Why XM Series Construction at 2,500 PSI Electric Drive?

The Commercial Platform Advantage for High-Duty Electric Wash Stations

The XMV3G25D-F33C2I is the correct specification when the application demands more than standard electric-drive pump construction can sustain reliably across a commercial duty cycle:

• Continuous-duty fixed wash stations — facilities running electric wash stations 8–16 hours per day, multiple shifts, impose cumulative stress on manifold seals, valve seats, and plunger surfaces that standard commercial-duty XTV platforms absorb over shorter service intervals. The XM Series manifold density, valve geometry, and crankcase architecture are specified for the structural margin that high-cycle continuous-duty environments demand.
• High-utilization rental installations — rental units in commercial accounts running multiple users per day accumulate operating hours faster than privately owned equipment. The XM Series’ additional structural margin translates directly into longer rebuild intervals and higher availability between service events in high-utilization rental environments.
• Applications approaching 2,500 PSI continuously — at operating pressures near the upper limit of standard commercial electric-drive pump platforms, the XM Series provides the structural and thermal headroom that prevents the accelerated wear at seals, valves, and manifold that occurs when standard platforms operate at or near their rated ceiling.
• Fleet and facility operators prioritizing total cost of ownership — the XM Series’ longer service intervals, individually rebuildable wear components, and AR North America domestic parts availability make the total cost of operating an XMV3G25D-F33C2I for 10 years measurably lower than replacing less durable alternatives multiple times over the same period.

Integrated Chemical Injection at 2,500 PSI — Complete Two-Mode Electric Wash Workflow

Pre-Soak, Degrease, and Rinse From a Single Factory-Assembled Electric Platform

The integrated downstream chemical injector on the XMV3G25D-F33C2I delivers full two-mode wash capability in a fixed electric wash station without additional injector hardware:

• Venturi-driven downstream injection — the injector built into the Gymatic unloader body draws detergent, degreaser, or pre-soak solution from a supply container using the venturi pressure differential created when the operator switches to low-pressure application mode. No chemical pump, powered dosing system, or electrical supply is required for basic detergent application.
• Two-mode workflow — low-pressure detergent pre-soak followed by full 2,500 PSI rinse reduces total wash time, chemical consumption, and physical scrubbing effort compared to pressure-only washing — particularly effective on fleet vehicles, equipment surfaces, and facility floors where contamination benefits from chemical dwell time before rinsing.
• No separate injector hardware required — the complete two-mode system is factory-assembled into the pump. One assembly. Two operating modes. No additional plumbing fittings needed for basic detergent application.
• Injector maintenance — flush the injector circuit with clean water after every detergent session to prevent chemical residue buildup in the venturi passage, preserving long-term injector function as detailed in the included operator’s manual.

The Gymatic Unloader — Tamper-Resistant 2,500 PSI Control with Chemical Feed

Set It Once. Run It All Day.

The Gymatic unloader (C2) on the XMV3G25D-F33C2I is rated above the pump’s 2,500 PSI operating pressure — within AR’s accepted 15% upside variance. At 2,500 PSI in a continuous-duty electric wash station, unloader stability and tamper resistance directly affect surface consistency and pump longevity:

• Tamper-resistant once set — locked pressure is maintained consistently across every operator and every shift without re-adjustment or drift, ensuring repeatable wash results in managed facility and fleet environments
• Internal bypass operation — trigger-off bypass smoothly redirects flow, preventing deadhead pressure spikes that accelerate seal and valve wear during idle intervals in continuous-run installations
• Motor load reduction in bypass — reduced back-pressure in trigger-off bypass mode lowers motor amperage draw and heat accumulation, protecting motor windings in continuous-use electric wash station environments
• Brass body construction — resists corrosion from cleaning chemicals, sanitizers, chlorinated supply water, and sustained indoor or outdoor exposure

XM Series Material Construction — Built for Commercial Continuous-Duty Life

Every Component Specified for 2,500 PSI Sustained Operation

• Solid ceramic plungers resist the elevated seal contact forces at 2,500 PSI across the high cycle counts of continuous-duty commercial wash stations. Their hardness and dimensional stability far exceed stainless alternatives, and when plungers approach service limits they are replaced individually — all other components remain in productive service.
• Forged brass manifold provides a dense, pore-free pressure vessel that withstands the cyclic mechanical stress, chemical exposure from detergent solutions drawn through the downstream injector, and thermal cycling of electric motor-driven continuous-duty operation without the structural degradation that limits cast aluminum manifolds under sustained commercial conditions.
• Stainless steel valves maintain precise seating geometry through hundreds of thousands of 2,500 PSI pressure cycles, resisting calcium scale accumulation and pitting that cause pressure loss and valve chatter at commercial operating pressures.
• Triplex three-plunger design produces smooth, overlapping pressure pulses that reduce pulsation-induced fatigue stress on hoses, spray guns, and fittings throughout the wash station system.

Typical Applications

Where the XMV3G25D-F33C2I Delivers Best Results

• Continuous-duty commercial electric wash stations — fixed wash points in fleet yards, manufacturing facilities, and commercial properties running multiple shifts where XM Series durability reduces service frequency and maximizes uptime
• High-utilization rental installations — rental units in commercial accounts with high daily use cycles where longer rebuild intervals and XM Series construction reduce total maintenance cost per rental hour
• Fleet and vehicle washing facilities — fixed electric wash bays for trucks, vans, trailers, and service equipment where 2,500 PSI output and integrated chemical feed support efficient two-mode wash workflows
• Indoor commercial wash bays — electric operation eliminates exhaust and noise; integrated chemical feed supports pre-soak and degreasing workflows without additional injector hardware
• Food and beverage facility washdowns — where electric operation, chemical-resistant XM Series construction, integrated sanitizer injection capability, and continuous-duty reliability are all operational requirements
• Industrial facility maintenance stations — production floor equipment washdowns, conveyor cleaning, and surface prep where sustained 2,500 PSI output and chemical application capability are both required
• Custom OEM electric wash skid builders — system integrators specifying XM Series commercial construction for electric-driven applications where standard XTV platform durability is insufficient for the intended duty cycle

5-Year US Warranty, Full Rebuildability, and Wholesale Pricing

Domestic Support Built to Last as Long as the Pump

The XMV3G25D-F33C2I is protected by Annovi Reverberi’s 5-year limited warranty through AR North America’s US-based warranty and service network. Every internal wear component — solid ceramic plungers, brass manifold seals and o-rings, stainless valve seats and springs, Gymatic unloader service parts, and crankcase bearings — is stocked domestically through AR’s authorized distribution channels.

With consistent maintenance — break-in oil change at 50 hours, scheduled oil changes every 500 hours or 3–5 months, regular valve and seal inspection at the service frequency appropriate for 2,500 PSI continuous-duty cycles, chemical injector circuit flushing with clean water after every detergent session, and proper winterization using RV-grade environmentally safe antifreeze — the XMV3G25D-F33C2I is engineered for 10 or more years of productive commercial service life. AR North America’s domestic parts depth ensures rebuild kits, plunger sets, and Gymatic unloader service components are typically available same-week, keeping high-duty electric wash operations running rather than waiting on international shipping timelines.

Contractors, rental fleet operators, facility managers, resellers, and volume buyers are invited to contact wholesale@wshpwr.com for wholesale and special pricing on the XMV3G25D-F33C2I and the full Annovi Reverberi pump and unloader assembly line. WSHPWR stocks more than 1,900 AR North America products — one of the most complete AR inventories available through any US web store.

XM Series Commercial Construction. Electric Drive. Integrated Chemical Feed. 2,500 PSI.

Italian Engineering. NEMA 56C Simplicity. US Warranty Coverage.

For facility managers, fleet operators, OEM system builders, and rental fleet operators who need the durability and structural margin of AR’s XM Series commercial platform in an electric motor-driven configuration with integrated chemical injection capability, the XMV3G25D-F33C2I delivers a factory-tested, fully documented, and completely rebuildable assembly from one of the global pressure pump industry’s most trusted manufacturers. Three thousand PSI-class construction. Electric drive. NEMA 56C interface. Gymatic bypass with integrated injector. Five years of US warranty. A decade of service life.

Volume buyers, resellers, and rental fleet operators can reach the WSHPWR wholesale team directly at wholesale@wshpwr.com to discuss pricing for quantity purchases across the complete Annovi Reverberi lineup — including pumps, unloader assemblies, and service parts.