AL-PLUG1/4B | 1/4 F Quick-Connect Plug, Brass

AL-PLUG1/4B | 1/4 F Quick-Connect Plug, Brass

The AR AL-PLUG1/4B — 1/4 in Female QC Plug is a compact, precision-machined brass
quick-connect plug engineered by Annovi Reverberi for fast attachment, secure sealing, and repeatable
performance in professional and residential pressure-washer setups. Its standard
1/4-inch female quick-connect profile snaps onto matching male couplers in seconds,
enabling tool-free swaps while maintaining a smooth, leak-resistant flow path from pump to nozzle.

Built from solid brass for corrosion resistance and long service life, the AL-PLUG1/4B helps technicians
move quickly between tips and accessories without sacrificing pressure, spray quality, or operator
confidence.

Construction & Design

Brass Body, Precision-Machined Sealing Surfaces

• Solid brass construction resists rust, chemical exposure, and outdoor conditions for dependable daily use.
• Precision-machined sealing land lets the companion O-ring seat cleanly, supporting a tight, bubble-resistant joint.
• Compact, rigid (non-swivel) body provides a stable connection that resists vibration and torsional stress.
• Smooth internal bore minimizes turbulence and pressure drop, helping maintain clean spray patterns at the wand.

The plug’s polished exterior eases insertion and release—even with wet gloves or light chemical residue—
while the compact hex profile offers positive tool purchase when needed without adding snag-prone bulk.

Quick-Connect Performance

Fast, Tool-Free Swaps with Stable Hydraulics

The AL-PLUG1/4B uses a standard 1/4 in female QC interface to mate with common male stems on
hoses, guns, lances, foam cannons, turbo nozzles, and surface cleaners.

• Push-to-lock engagement eliminates thread starting, cross-thread risk, and wrench work during accessory changes.
• Firm, centered detent helps the coupler’s O-ring compress evenly for a dry, reliable seal through repeated cycles.
• Full-flow internal passage supports steady unloader behavior and consistent impact across a wide range of tips.
• Reduced weeping helps keep work areas drier and safer, while protecting pumps, hoses, and fittings from nuisance leaks.

In everyday use this means quick transitions—wide-fan pre-rinse, foam application, rotary agitation, and
final rinse—without hunting tools or re-plumbing connections.

Installation & Use

Simple, Familiar QC Procedure

• Confirm the mating male coupler is clean and its O-ring is intact and properly lubricated.
• Insert the male stem squarely into the AL-PLUG1/4B until the detent clicks into place.
• Pull lightly to verify lock-in before pressurizing the system.
• To disconnect, pull back the coupler sleeve and withdraw the accessory in a controlled motion.

Because the plug follows common industry geometry, it integrates easily with mixed fleets and helps
standardize connection feel across bays, carts, and mobile rigs—reducing training time and adapter clutter.

Care & Maintenance

Keeping Connections Clean and Leak-Free

• Rinse chemical residue from the plug at the end of the shift and wipe the sealing face clean.
• Visually inspect the companion O-ring in the male coupler; replace if flattened, nicked, or cracked.
• Check for impact damage or deformation around the hex and nose; replace the plug if geometry is compromised.
• Store hoses and guns so the plug is not dragged on concrete or contaminated with grit that could abrade seals.

Replacing worn or mismatched fittings with a correctly sized AR plug restores the intended geometry so
couplers lock smoothly, release predictably, and hold pressure at working flow.

Typical Applications

• Mobile detailing rigs and automotive wash bays needing rapid tip and lance changes.
• Rental fleets and contractor trailers standardizing on 1/4 in QC connections for user-friendly setups.
• Industrial and agricultural wash stations where accessories are swapped frequently throughout the day.
• Residential prosumer units upgraded for foamers, turbo nozzles, and specialty tools.

AL-PLUG1/4B | 1/4 F Quick-Connect Plug, Brass

The AR AL-PLUG1/4B – 1/4 in Female QC Plug is a compact, brass quick-connect fitting that
turns accessory changes into a quick, confident motion while maintaining a clear, leak-resistant hydraulic
path from pump to point of work. Its robust construction, precise machining, and universal 1/4 in female
QC format make it a practical, cost-effective upgrade wherever fast swaps and dependable sealing are
priorities.