5221 | 36 in Aluminum Lance, High-Pressure Lightweight Wand

5221 | 36 in Aluminum Lance, High-Pressure Lightweight Wand

The AR 5221 — 36 in Aluminum Lance | Lightweight, Corrosion-Resistant Spray Wand is a
36-inch aluminum spray lance built to give operators extra reach, lighter handling, and dependable
control for frequent high-pressure cleaning in bays, shops, and facility maintenance. Its strong,
corrosion-resistant aluminum tube holds a steady standoff over long passes on vehicles, siding, shop
floors, equipment frames, and masonry while keeping overall weight low so hands and forearms stay
fresher through the end of the shift.

5221 Three feet of length hits a practical sweet spot: long enough to reach wheel housings, rooflines, tall
panels, eaves, and hard-to-access angles, yet compact enough to maneuver cleanly around trailers,
racks, lifts, guards, and plant equipment where space is tight. The lance’s straight, rigid geometry
tracks predictably, helping the nozzle meet the surface squarely for uniform impact and fewer streaks
as you sweep across concrete or rinse large vertical surfaces.

5221 | 36 in Aluminum Lance, High-Pressure Lightweight Wand

Key Features & Benefits

• 36-inch balanced reach: Provides extra reach for tall panels, soffits, and hard-to-access angles while remaining manageable in tight bays and around equipment.
• Lightweight aluminum tube: Low mass reduces operator fatigue while maintaining the stiffness needed for a steady standoff and precise spray angle.
• Corrosion-resistant construction: Stands up to wet, detergent-rich environments and daily wash cycles without the surface oxidation that can roughen handling.
• Rigid, straight geometry: Keeps the nozzle square to the work so sweeps across concrete, pavers, and siding stay even and free of banding.
• Clean internal bore: Supports smooth flow so pump energy reaches the nozzle rather than dissipating in the wand, preserving strong, predictable spray patterns.
• Compact inlet layout: Keeps the connection close to the lance’s axis for a balanced feel and less leverage on upstream fittings.
• Non-slip grip area: Firm, secure grip improves control when the wand is wet and reduces the micro-corrections that tire hands during detailed work.

Operation & Technique 5221 | 36 in Aluminum Lance, High-Pressure Lightweight Wand

Day-to-day use is straightforward and deliberate. Route the supply hose with gentle bends so movement
stays free, make sure chosen couplings and adapters are clean and properly seated, and select a tip that
matches the task—wide fan for rinsing, narrower pattern for cutting, or an adjustable assembly when you
want to tune impact on the fly.

On vehicles, begin with a pre-rinse to float loose soil, apply detergent per system instructions, then
rinse from top to bottom at a controlled distance to prevent redeposit. On concrete, pavers, and shop
slabs, maintain a consistent standoff and smooth traverse to avoid banding, finishing with a rinse pass
to clear fines. Around equipment and building details, ease off at gaskets, seals, louvers, electrical
housings, and bearings not intended for direct impact, and use the lance’s reach to keep the gun hand
out of splash and overspray.

For training new operators, emphasize a steady stance, overlapping lanes, and a measured pace—simple
fundamentals that let the 5221 lance’s length and low weight do the heavy lifting while delivering clean,
repeatable results.

Best Practices & Maintenance 5221 | 36 in Aluminum Lance

• Safe changeovers: Depressurize before swapping nozzles or accessories; keep threads and quick-connects (if used) free of grit and never use the lance as a lever to lift heavy attachments.
• End-of-shift flushing: Flush clean water through the assembly to purge detergents, then wipe the exterior to remove film so inspection is quick and any nicks are visible.
• Proper storage: Store the wand on a rack rather than under weight that could bend accessories or the tube.
• Leak and pattern checks: If a joint weeps, re-seat the adapter or replace a tired seal; if the stream wanders, inspect the tip for debris and verify that standoff and angle keep the jet perpendicular to the target.

5221 | 36 in Aluminum Lance, High-Pressure Lightweight Wand

In car wash bays and fleet maintenance, the AR 5221 shortens setup at the start of each
shift, supports efficient soap-and-rinse sequences, and keeps operators at a comfortable, consistent
distance from splash. In facilities work, it helps reach soffits, louvers, screens, stair stringers,
and machine bases without constant ladder moves or awkward body positions. On equipment, it lets you
wash under rails, along frames, and behind guards while keeping the gun hand out of the worst ricochet.

By combining a practical 36-inch aluminum tube with balanced handling and corrosion-resistant
durability, the AR 5221 serves as a sturdy, everyday lance that improves reach, accelerates
changeovers in modular builds, and delivers consistent, professional results across vehicles,
facilities, and industrial cleaning tasks.