5226 | 12 in Aluminum Lance, Targeted Cleaning Wand

5226 | 12 in Aluminum Lance with QC Plug, Targeted Cleaning Wand

The AR 5226 — 12 in Aluminum Lance | Quick-Connect Plug, Compact Reach is a 12-inch
aluminum spray lance with an integrated quick-connect plug that delivers rapid assembly, precise
control, and durable, corrosion-resistant performance for targeted cleaning in bays, shops, and tight
spaces. Designed for compact reach, lighter handling, and fast setup, it serves as a dependable
everyday wand for close-in, high-pressure cleaning.

5226 aluminum tube keeps weight down without sacrificing stiffness, so you can hold a steady standoff on
close-in work—wheel wells, engine bays, steps, fixtures, equipment frames, and masonry details—while
reducing arm fatigue compared to heavier steel sticks. The integrated quick-connect plug drops into a
compatible socket with a simple collar pull-and-snap, turning changeovers into a quick, repeatable
motion that fits shop routines and mobile workflows. Twelve inches is the right length when space is
tight: long enough to keep your hand away from splash and heat, short enough to maneuver around
trailers, racks, guards, and conveyors without fighting the hose. Balanced geometry helps the lance
track straight so the nozzle meets the surface squarely, delivering uniform impact and fewer streaks as
you work along edges, around brackets, and across small panels.

5226 Key Features & Benefits

• 12-inch compact reach: Optimized for tight spaces and detail zones where a longer wand
  is clumsy—wheel wells, engine bays, steps, fixtures, and close-clearance hardware.
• Integrated quick-connect plug: Drops into compatible sockets with a simple
  pull-and-snap for fast, repeatable tool changes that keep up with shop and mobile workflows.
• Lightweight aluminum construction: Keeps mass low without sacrificing stiffness, so you
  can hold a precise standoff and reduce arm fatigue during long shifts.
• Balanced, straight geometry: Helps the nozzle stay square to the work for uniform
  impact and fewer streaks as you move along edges and around brackets.
• Corrosion-resistant performance: 5226 aluminum body resists corrosion in wet,
  detergent-rich environments, and the clean bore supports smooth flow so pump energy reaches the
  nozzle instead of dissipating at the lance.
• Compact, non-slip grip: Firm grip section improves control when the wand is wet, while
  the short length reduces micro-corrections that tire hands and forearms.
• Space-saving form factor: Compact body saves room on carts and in vehicle bins so rigs
  stay tidy and organized.

Operation & Technique

Day-to-day use is straightforward. Route the supply hose with gentle bends for free movement, seat the
quick-connect cleanly, and confirm engagement with a light tug. Choose a tip matched to the
task—wide fan for rinsing, narrower pattern for cutting, or variable nozzles for on-the-fly adjustment—
and keep a measured pace that overlaps lanes for an even finish.

On vehicles, pre-rinse to float loose soil, apply detergent per system instructions, then rinse from top
to bottom at a controlled distance to prevent redeposit. On concrete pads, stairs, and shop slabs,
maintain a consistent standoff and smooth traverse to avoid banding, finishing with a rinse pass to
clear fines. Around equipment, ease off at seals, gaskets, electrical housings, and bearings that are
not intended for direct impact, using the lance’s reach to keep the gun hand out of spray and heat.

5226 Best Practices & Maintenance

• Quick-connect care: Keep the plug and mating socket clean—grit at the seal can create
  nuisance drips. If coupling feels rough, clean the socket and lightly lubricate per standard practice.
• Safe changeovers: Depressurize before swapping tips or accessories, and avoid using the
  lance as a lever to lift heavy attachments.
• After-chemical flushing: After chemical use, flush clean water through the lance and
  cycle the trigger briefly to clear residual detergent.
• Exterior cleaning & storage: Wipe the exterior to remove film so inspection is fast,
  and store the wand on a rack rather than under weight that could bend attachments or the tube.
• Leak diagnosis: If a drip persists, inspect the socket’s internal seal and the plug
  nose, then re-seat once surfaces are clean and in good condition.
• Operator technique: Emphasize a steady stance, constant standoff, and overlapping lanes
  that blend cleanly so the wand’s balance and short length can do the handling.

5226 | 12 in Aluminum Lance with QC Plug, Targeted Cleaning Wand

Applications

In car wash bays and service shops, the 5226 speeds assembly at the start of each
shift, supports efficient soap-and-rinse sequences on close-in work, and keeps operators at a
comfortable distance from splash. In facilities, it helps reach corners, stair treads, machine bases,
louvers, and screens without moving ladders for every panel. On equipment, it lets you wash under
rails, along frames, and behind guards while keeping the gun hand out of spray and heat.

By combining a compact 12-inch aluminum tube, a reliable quick-connect plug, and handling that stays
light and predictable, the AR 5226 provides an everyday lance that improves reach in tight spaces,
accelerates changeovers, and delivers consistent, professional results across vehicles, facilities, and
industrial cleaning tasks.