AR4221600 | Brass Garden Hose Adapter, GHA Inlet Fit

AR AR4221600 Brass Garden Hose Adapter for GHA Inlet

Product Configuration

• AR4221600 is a brass garden hose adapter engineered by Annovi Reverberi to create a secure, leak-free interface between standard garden hoses and GHA pump inlet fittings.
• Designed to stabilize inlet connections in residential, contractor, and light industrial pressure washing systems where consistent feed water is required.
• Solid brass body provides a durable mechanical connection that holds thread engagement under vibration and repeated connection cycles.
• Precision thread geometry supports predictable sealing and reduces the chance of cross-threading during hand installation.
• Internal bore is designed to maintain unrestricted inlet flow to support pump efficiency and stable operation.

Key Features

• Solid brass construction for long service life in wet and outdoor environments.
• Corrosion-resistant material selection reduces oxidation and thread degradation.
• Precision-machined threads designed for secure engagement and leak control.
• Standard 3/4" garden hose connection for broad compatibility.
• Engineered to fit Annovi Reverberi GHA pump inlet fittings.
• Hand-tight installation supported by stable thread start and clean engagement.
• Wide internal passage designed to reduce restriction at the inlet.
• Connection stability supports consistent water delivery during operation.
• Suitable for hot and cold water service within typical pressure washer inlet conditions.
• Designed to remain stable under pressure surges and equipment vibration.

Materials and Construction Standards

• Solid brass provides mechanical stability and consistent thread strength.
• Material selection resists rust and reduces cracking risk compared to plastic adapters.
• Brass construction tolerates repeated tightening cycles without deforming sealing surfaces.
• Surface finish supports easy cleaning and reduces debris buildup on the fitting body.
• Thread engagement integrity supports long-term use in mobile and fixed installations.

Compatibility and Fitment

• Fits standard 3/4" garden hose connections commonly used on pressure washer supply lines.
• Designed for a direct fit to Annovi Reverberi GHA pump inlet fittings.
• Compatible with pressure washer setups requiring a 3/4" hose adapter interface.
• Suitable for homeowner systems, contractor skids, and service rigs using garden hose supply feeds.
• Verify inlet thread style on the receiving component to confirm correct application.

Flow and Performance Benefits

• Supports stable, uninterrupted inlet water supply to the pump during operation.
• Smooth internal water path minimizes pressure loss at the connection point.
• Leak control reduces air intrusion at the inlet connection.
• Improved connection stability supports consistent pump response under changing load.
• Reduced inlet restriction helps protect volumetric efficiency and supports quiet operation.

Installation Guidance

• Thread-on installation designed for hand tightening without special tools.
• Start threads square to the inlet to ensure clean engagement and avoid cross-threading.
• Hand-tighten to a firm seated condition and verify there are no drips under flow.
• Optional sealing washer or O-ring may be used where the receiving interface requires it.
• Confirm hose gasket condition and replace worn gaskets to maintain a leak-free connection.

Maintenance and Service

• Rinse after use to remove grit, detergent residue, or mineral deposits from exterior surfaces.
• Inspect threads periodically for damage from repeated connection cycles.
• Apply a light silicone lubricant or plumber’s grease to threads if frequent assembly is expected.
• Replace hose washers as needed to maintain consistent sealing at the garden hose connection.
• Brass construction is designed for extended service life under normal pressure washer duty.

Quality Control and Manufacturing

• Precision-machined threads and sealing surfaces support consistent fit and sealing behavior.
• Internal diameter consistency supports repeatable inlet flow characteristics.
• Produced under Annovi Reverberi manufacturing standards for dimensional control.
• Designed to perform reliably in common pressure washer inlet configurations.
• Inspection standards focus on thread quality, sealing surfaces, and overall finish.

Selection Rationale

• Durable brass construction supports reliable hose-to-inlet connections in daily use.
• Leak-resistant design improves inlet stability and helps protect pump operation.
• Standard 3/4" garden hose interface supports broad compatibility across supply hoses.
• Direct-fit intent for GHA pump inlet fittings simplifies replacement and system standardization.
• Service-friendly design supports quick connection checks and fast field replacement.